[DMCForum] Re: One nit-picky question

["cruznmd" <racuti1@xxxxxxxxxxxx>]

When you say "piston screw" you're referring to the spring-loaded 
chain tensioner release screw right?

If you are, I don't see how you could not have it set properly if the 
timing chains are all installed and the cam sprockets are in place. 
The tensioners automatically set themselves once in place. 

For instance, a new chain is nice and tight and the tensioner is 
totally retracted, butting up against the chain. The volvo manual I 
have states that if the tensioner has extended so many clicks to take 
up slack in a stretched chain, to replace the chain.

Meaning, I don't know how you could have -not- reset the tensioner. :)

Martin was adamant that new chains would give the engine new life, 
and I don't doubt him for a minute, but my engine has low miles and 
the tensioners had not extended any clicks out. In fact, until I 
torqued my heads down, the chains were -too- tight. Torqueing them 
down gave what I would say was just enough slack to be safe.

--- In DMCForum@xxxxxxxxxxxxxxx, Travis Goodwin <tgoodwin@xxxx> wrote:
> Yeah. I wasn't afraid of it being in the oil pan. I should be so 
lucky. 
> 
> I let it eat at me and eat at me all day long so I took the cover 
off. After
> a few minutes of searching I gave up and was about to put the cover 
back on
> when I found it, wedged between the two of the chains and the drive 
shaft. I
> had to turn the engine a little and was able to free it. It's now 
in its
> rightful place.
> 
> Needless to say, now I'm running over in my head all the details. 
Now I'm
> wondering if I reset timing chain piston screw. I'm 90% sure I did 
but this
> whole washer incident has got me all flustered.
> 
> > -----Original Message-----
> > From: John Hervey [mailto:john@xxxx]
> > Sent: Tuesday, August 19, 2003 9:56 PM
> > To: DMCForum@xxxxxxxxxxxxxxx
> > Subject: RE: [DMCForum] Re: One nit-picky question
> > 
> > Travis, I have had worse fall into the oil pan. The oil pump 
won't pick it
> > up. It will just lye around and bug the hell out of you till you 
take it
> > out. If it was smaller than the pan drain, then next time you 
change the
> > oil, put a magnetic extender into it and try to fish it out.
> > John Hervey
> > www.specialTauto.com
> > 
> >   -----Original Message-----
> >   From: Travis Goodwin [mailto:tgoodwin@xxxx]
> >   Sent: Monday, August 18, 2003 6:33 AM
> >   To: 'DMCForum@xxxxxxxxxxxxxxx'
> >   Subject: RE: [DMCForum] Re: One nit-picky question
> > 
> > 
> >   If it fell into the oil pan it would spend its life lounging 
there. I
> > never
> >   saw it in or around the chains. I even turned the engine over a 
bunch of
> >   times to verify there was nothing in there.
> > 
> >   > -----Original Message-----
> >   > From: cruznmd [mailto:racuti1@xxxx]
> >   > Sent: Monday, August 18, 2003 9:40 AM
> >   > To: DMCForum@xxxxxxxxxxxxxxx
> >   > Subject: [DMCForum] Re: One nit-picky question
> >   >
> >   > It may not be critical to operation but you'll experience 
what we in
> >   > the Navy call FOD. Foreign Object Damage.
> >   >
> >   > Having a stray piece of metal drifting around in your timing 
chain
> >   > cover riding the oil currents is probably not a good idea.
> >   >
> >   > Ask the others though. I may be overstating the situation.
> >   >
> >   > --- In DMCForum@xxxxxxxxxxxxxxx, Travis Goodwin 
<tgoodwin@xxxx> wrote:
> >   > > Okay, bare with me as I attempt to explain my situation.
> >   > >
> >   > > During my procedure of replacing the RS cam sprocket, I had 
to get
> >   > into the
> >   > > timing cover and push the piston back in to slacken the 
chain. That
> >   > didn't
> >   > > give me quite enough room so I removed the tensioning arm 
just
> >   > below it.
> >   > > This gave me the room I needed to slip the sprocket back on.
> >   > >
> >   > > However, when I took the tensioning arm off, I thought I 
heard the
> >   > distinct
> >   > > jingle of metal falling and hitting metal. I never saw 
anything and
> >   > could
> >   > > never figure out what fell. Apparently a washer that rests 
against
> >   > the
> >   > > engine block fell when I removed the tensioner.
> >   > >
> >   > > If you look at items 12, 13, and 14 you'll see my concern.
> >   > >
> >   > > http://www.usadmc.com/dmcstore/ViewDir.asp?
PageID=9&PageCat=1%
> >   > 2DEngine
> >   > >
> >   > > My question is, how crucial is this little washer? Should I 
take
> >   > the cover
> >   > > off (oh jeez, not again) and reinstall it?
> >   >
> >   >
> >   >
> >   > To unsubscribe from this group, send an email to:
> >   > DMCForum-unsubscribe@xxxxxxxxxxxxxxx
> >   >
> >   >
> >   >
> >   > Your use of Yahoo! Groups is subject to
> > http://docs.yahoo.com/info/terms/
> > 
> > 
> >         Yahoo! Groups Sponsor
> >               ADVERTISEMENT
> > 
> > 
> > 
> > 
> >   To unsubscribe from this group, send an email to:
> >   DMCForum-unsubscribe@xxxxxxxxxxxxxxx
> > 
> > 
> > 
> >   Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
Service.
> > 
> > 
> > [Non-text portions of this message have been removed]
> > 
> > 
> > 
> > To unsubscribe from this group, send an email to:
> > DMCForum-unsubscribe@xxxxxxxxxxxxxxx
> > 
> > 
> > 
> > Your use of Yahoo! Groups is subject to 
http://docs.yahoo.com/info/terms/

Yahoo! Groups Sponsor

To unsubscribe from this group, send an email to:
DMCForum-unsubscribe@xxxxxxxxxxxxxxx



Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.