[DMCForum] Re: damnit to hell (my poor engine)
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[DMCForum] Re: damnit to hell (my poor engine)




This was a most interesting thread (the subject line right out of my
lips).

I am reasonably sure at this point I will have to reassess the
condition of my engine (PRV/B280f in a...umm...Volvo...).

I have some more questions:

1. How does one properly bleed the cooling system on one of these?

2. Would a compression test reveal a faulty head gasket? I have good
compression on all 6 cylinders (180-185psi, maybe too good?).

3. Would a head gasket that is bad or heading that way cause excess
pressure in the cooling system?

The engine is running strong but I have had a couple high
temp 'incidents'. And chocolate milkshake in the oil filler which was
there before though.

Carter

--- In DMCForum@xxxxxxxxxxxxxxx, "therealdmcvegas" <dmcvegas@xxxx>
wrote:
>
> --- In DMCForum@xxxxxxxxxxxxxxx, "Matt Spittle" <mds328@xxxx> wrote:
> <SNIP>
> > Will running a coolant pressure test verify if I have a blown
head
> > gasket?
> >
> > thanks,
> >
> > Matt
> > #1604
>
> Most definetly. You'll be pressurizing the cooling system, and
forcing
> water out of any leaks that you have. I had lots of coolant in the
> "Valley of Deat" too, when one of the O-Rings on the Y-Pipe finally
> rotted away, and allowed fluid to flow out freely. So you'll want to
> snag a couple of new rings down at the local autoparts store when
you
> pick up the pressure testing kit. BTW, don't bother looking for the
> rings in the aisle. They're in a box behind the counter.
>
> But first, let's talk about what causes a head gasket to prematurely
> fail. Heat is the enemy here. And you know that if you severely
> overheated an engine, the cylinder heads warp and seperate
themselves
> from the headgasket. Obviously at that point you need to replace
both
> the cyliner head, and the head gasket. But, there is also another
> silent killer of headgaskets, and it too is caused by heat.
>
> Improperly bled cooling system: That's right. If you've got air in
the
> engine, you're gonna SEVERLY shorten the life of the headgasket. It
> works like this. Cast Iron cylinder sleeves will heat up and expand
> and a far slower rate than the Aluminium cylinder heads. However,
when
> we have coolant flowing across them both, the heat is gently
> transfered between the two, and they both heat and expand at a much
> more syncronized rate.
>
> But air inside the cooling system negates all this. Water doesn't
flow
> across the surfaces evenly, and pockets of air them become steam
> pockets. Now keep this in mind: Steam is a gas so it rises, and it's
> the aluminum cylinder heads up that are on the top. The water below
> may only be like 120°F during the warm up, but the steam pockets
have
> already hit 260°F+! So the Aluminum expands much more quickly than
the
> Cast Iron below. What happens here is that the head gaskets are
slowly
> torn, because the two sides between it are shifting in different
> directions.
>
> And DeLoreans are tricky to the average mechanic, when it comes to
> diagnosing bad headgaskets just by sight.
>
> Because of that damn valley under the intake manifold, it's easy to
> believe that the car has a bad head gasket. You leak out fluid, but
it
> never drips below the car. Instead, it collects up above, and gets
> boiled off. And then when a car isn't always run up to temperature,
> the condensation inside is easily mistaken for coolant in the oil.
> Although I too have concerns about that crap in the oil filler cap
for
> your engine.
>
> Do this:
> Step 1. Pressure test a FULL cooling system. 14½ PSI for 15 minutes,
> and the fluctuation should be minimal, if at all.
>
> If no leaks detected, move on to step 2. If leaks are found, repair
> them before proceeding. Remeber, you're dealing with coolant hoses,
a
> radiator, engine block, AND the heater core inside. So check all
these
> areas IF the pressure isn't able to maintain itself.
>
> Remove the rocker covers, and pull the oil drain plug. See if any
> water sprays, or otherwise visably drips out of any of these places.
> That'll find out what's going on with the engine.
>
> Step 2: If/when no leaks are present, reassemble the top end with
new
> seals, hoses, etc. Use silicone hoses for the water pump, new rubber
> tubes for the vacuum lines, new orings for the intake manifold, new
> oil resistant hoses for the breather tubes, etc. SEAL EVERYTHING!
Make
> certain that there are no vacuum leaks.
>
> Step 3: Disconnect the Oxygen sensor from the ECU wire, so that the
> engine will stay in "limp mode", and won't fiddle with the O2
mixture
> on you. Start the engine, and see how she runs. Since you had vacuum
> leaks before, you're prolly gonna need to adjust the CO mixture to
get
> the car running right. So if you need to fiddle with it right now to
> get the car running right, that's OK.
>
> Step 4: Once the engine is cool, flush it with this (2nd from the
bottom):
> http://www.berrymanproducts.com/Default.aspx?tabid=139
> This is POWERFUL stuff. It dissolves anything (including styrofoam),
> and will clean out your motor. You'll only need about &#8532; of
the bottle.
> Pour it directing into the crankcase, and idle the motor for about 7
> minutes. Then shut the motor off, and drain the oil & cleaner out
ASAP.
>
> After that you can drive the car to your local old skool Volvo
> mechanic where you can reattach the O2 sensor, and get the CO
balanced
> on the motor. But I would first add that you pour some Techron into
> the tank, and burn out the old gasoline first, and refill with fresh
> before tuning the CO on the car.
>
> -Robert





Yahoo! Groups Links



Home Back to the Home of PROJECT VIXEN 


Copyright ProjectVixen.com. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive

This site contains affiliate links for which we may be compensated