Re: [DML] Fuse box replacement
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [DML] Fuse box replacement



I will check the type of solder I'm using, I know it's rosin core and it says ideal for all electronics repairs.  

Those soldering stations look like the cat's meow, however this is the most soldering I've done in my life and I doubt I will do this much again anytime soon.  I don't think I can justify buying one!  I'll probably just keep on with my gun but I'll be sure to follow Nick's advice and use minimal solder.  I think I'm doing a good job so far, it's just tedious but what did I expect????

Andy



--- In dmcnews@xxxxxxxxxxxxxxx, "jtrealtywebspannet" <jtrealty@...> wrote:
>
> It also helps if you clean the tip often and then melt a little solder (tin) onto it. You should also be using 1/16 rosin core or smaller. An iron is nice because you do not have to always heat it up again after putting it down.
> David Teitelbaum
> 
> --- In dmcnews@xxxxxxxxxxxxxxx, Michael Griese <mike.griese@> wrote:
> >
> > Andy - Those gun-style irons will be a challenge for what you are doing.  If you 
> > are ever near Rochester, I could loan you a soldering station I have that is 
> > perfect for this type of work.  I can also show you some techniques for making 
> > the joints quickly and consistently.
> > 
> > One thing that can help is to tin the wire (get solder to flow onto/into the 
> > wire), then try heating the joint.  
> > 
> > 
> >  --
> > Mike
> > 
> > 
> > 
> > 
> > ________________________________
> > From: Nick Kemp <nkemp@>
> > To: dmcnews@xxxxxxxxxxxxxxx
> > Sent: Mon, August 27, 2012 3:33:09 PM
> > Subject: Re: [DML] Fuse box replacement
> > 
> > Andy, Soldering is part art and part science. It is always difficult to 
> > solder "flying" wires because you can't get a solid contact between the 
> > iron and the wire and thus you don't get good heat transfer. If you 
> > could get something to put under the connection so that you can push 
> > against it while heating up the connection it will heat up faster. Don't 
> > use metal because it will soak up too much heat. Use something like wood 
> > or fiberglass sheets (like circuit boards)
> > 
> > Be careful melting the solder on the iron and not on the wire. It can 
> > result in cold solders. A cold solder will be dull and does not show 
> > good wicking. I find the best spot with problematic joints is that space 
> > between the iron and the wire. The wire is often hot enough to take/wick 
> > the solder for a good connection.
> > 
> > Don't flow too much solder. It makes the wires rigid and the weak point 
> > becomes the point where there is no solder (not the connection). This is 
> > especially true for high vibration connections. [It is a problem 
> > encountered by a few home built airplanes.] For that matter, many 
> > believe that a good crimp connection without solder is better than a 
> > good connection with solder.
> > 
> > And ALWAYS use rosin core solder. Many have tried to use plain solder 
> > (usually plumbing solder) and it will not take without using rosin with 
> > it. This is true for wiring, circuit boards and plumbing. But I suspect 
> > you already knew that.
> > 
> > See you at the Orchard.
> > 
> > Nick
> > 
> > 
> > soma576 wrote , ----On 8/27/2012 2:52 PM ---------------------------:
> > >
> > > Hey all,
> > >
> > > 11596 is getting a new fuse box. I've had a few of the critical fuses 
> > > in jumpers for well over a decade. I always hated messing around in my 
> > > electrical compartment for fear of knocking something loose and 
> > > causing Bad Things.
> > >
> > > I got the new fuse box kit from DMCMW and a proper barrel crimper. Not 
> > > only am I crimping everything perfectly but I'm also soldering the 
> > > connections. Should be trouble-free for a long time.
> > >
> > > Anyway the kit is coming along nicely but as you can expect it takes a 
> > > long time to do right. Took me about 4 hours just to do 7 fuses last 
> > > night. After crimping and soldering I'm putting 3/4" of heat shrink 
> > > tubing on the connection.
> > >
> > > One thing that baffles me is how long it can take to heat up the 
> > > connection so the solder will flow. I'm using a 140 watt gun-style 
> > > iron with flat blade tip. Once the tip is hot I can melt the solder on 
> > > the tip in less than a second, but it often takes well over a minute 
> > > to heat up the connector. It might have something to do with "tinning" 
> > > the tip - once I flowed some solder onto the tip, shook it off, then 
> > > went right for the connector which took solder in under 3 seconds. 
> > > Other times it takes what seems like forever.
> > >
> > > Anyone have any great tips to make this go faster?
> > >
> > > Andy
> > >
> > > 
> > 
> > 
> > 
> > 
> > ------------------------------------
> > 
> > To address comments privately to the moderating team, please address:
> > moderators@
> > 
> > For more info on the list, tech articles, cars for sale see www.dmcnews.com
> > 
> > To search the archives or view files, log in at 
> > http://groups.yahoo.com/group/dmcnewsYahoo! Groups Links
> > 
> > 
> > 
> > [Non-text portions of this message have been removed]
> >
>




------------------------------------

To address comments privately to the moderating team, please address:
moderators@xxxxxxxxxxx

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at http://groups.yahoo.com/group/dmcnewsYahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/dmcnews/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/dmcnews/join
    (Yahoo! ID required)

<*> To change settings via email:
    dmcnews-digest@xxxxxxxxxxxxxxx 
    dmcnews-fullfeatured@xxxxxxxxxxxxxxx

<*> To unsubscribe from this group, send an email to:
    dmcnews-unsubscribe@xxxxxxxxxxxxxxx

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/



Home Back to the Home of PROJECT VIXEN


Copyright 2006 ProjectVixen.com.  All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive