Re: [DMCForum] Re: ATTN: Andrei (Part III)
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [DMCForum] Re: ATTN: Andrei (Part III)



I think that is where my problem is.  The screw for the pass side was
cranked down by the PO or mechanic and the top broke off...  So I have no
way to adjust that bank other than the idle screw.  My idle is hovers
around
850.



Andrei



----- Original Message ----- 
From: "content22207" <brobertson@xxxxxxxxxxxx>
To: <DMCForum@xxxxxxxxxxxxxxx>
Sent: Tuesday, December 23, 2003 9:10 PM
Subject: [DMCForum] Re: ATTN: Andrei (Part III)


> Are you running off brass manifold screws? If so, try opening inlet
> screw a bit more. Don't forget to set balancing screws PROPERLY (see
> IDLE.TXT under Files section).
>
> Old Volvo PRV's idle at 900 RPM BTW. May have difficulty manually
> tuning to 750.
>
> Bill
>
> >--- In DMCForum@xxxxxxxxxxxxxxx, "Andrei Cular" <acular@xxxx> wrote:
> > I did try adjusting the screw but when I lean it out anymore it
> starts to
> > run really ruff.  Also I have no idea when this gas sniffer was last
> > calibrated so for all I know it might be running less than 5%
> already.  My
> > home made O2 sensor says that I am just on the rich side of ideal.
> >
> >
> > Andrei
> >
> >
> > ----- Original Message ----- 
> > From: "content22207" <brobertson@xxxx>
> > To: <DMCForum@xxxxxxxxxxxxxxx>
> > Sent: Tuesday, December 23, 2003 10:15 AM
> > Subject: [DMCForum] Re: ATTN: Andrei (Part II)
> >
> >
> > > Thought about this after "send" button was already pressed (but
> that
> > > message was long enough anyway):
> > >
> > > Nowhere did you mention turning CO2 screw to lean fuel mixture
> back to
> > > 5%. Why don't you try that before giving up on non-Lambda
> experiment.
> > >
> > > This isn't rocket science: Without Lamda the upper fuel
> distributor
> > > chambers are going to flex to a maximum size and stay there.
> That's
> > > it. That's the whole point -- to remove constant fluctuation of
> lower
> > > chambers by frequency valve. All you have to do then is adjust
> > > metering piston movement (with CO2 screw) to correspond to maximum
> > > upper chamber volume.
> > >
> > > Hopefully your family members are NOT lurking. My sister does, so
> now
> > > knows all my sexual predilections.
> > >
> > > Andrei the ENGINEER...
> > >
> > > Bill Robertson
> > > #5939
> > >
> > > >--- In DMCForum@xxxxxxxxxxxxxxx, "Andrei Cular" <acular@xxxx>
> wrote:
> > > > > Don't know how old you are, but I am old enough to remember
> what
> > > > > Detroit (and Kenosha!) went through in the 1970's:
> > > >
> > > >  Just turned 25, so I don't remember what they went through.
> > > However being
> > > > a car nut my whole life, helped my uncle rebuild an AMX when I
> was
> > > 5,  I am
> > > > familiar with the history.
> > > >
> > > > When a manufacture has something that works they are very slow
> to
> > > change it.
> > > > To get the full investment out of a design they usually will
> just start
> > > > bolting things on and making small tweaks till it is no longer
> > > possible to
> > > > get anymore from the engine.  Look at Porsche it tool them
> nearly 50
> > > years
> > > > to switch from air cooled to water cooling in the 911.
> > > >
> > > > > I am honest to goodness curious about your test results.
> Please post
> > > > > to Forum (am away from eMail until Sunday). This isn't a "he
> said/he
> > > > > said" issue -- I really think you can come up with some hard
> data that
> > > > > *SOME* owners will find useful (surely I am not the *ONLY*
> person who
> > > > > wants to return to basics).
> > > >
> > > > I'll keep you updated.
> > > >
> > > > > Andrei the scientist...
> > > > I'm and engineer not a scientist.  Sorry had to just incase any
> family
> > > > members are monitoring this group.
> > > >
> > > >
> > > > Andrei
> > >
> > >
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > > To visit your group on the web, go to:
> > >  http://groups.yahoo.com/group/DMCForum/
> > >
> > > To unsubscribe from this group, send an email to:
> > >  DMCForum-unsubscribe@xxxxxxxxxxxxxxx
> > >
> > > Your use of Yahoo! Groups is subject to:
> > >  http://docs.yahoo.com/info/terms/
> > >
> > >
>
>
>
>
> Yahoo! Groups Links
>
> To visit your group on the web, go to:
>  http://groups.yahoo.com/group/DMCForum/
>
> To unsubscribe from this group, send an email to:
>  DMCForum-unsubscribe@xxxxxxxxxxxxxxx
>
> Your use of Yahoo! Groups is subject to:
>  http://docs.yahoo.com/info/terms/
>
>



  _____  

Yahoo! Groups Links


*	To visit your group on the web, go to:
http://groups.yahoo.com/group/DMCForum/
  

*	To unsubscribe from this group, send an email to:
DMCForum-unsubscribe@xxxxxxxxxxxxxxx
<mailto:DMCForum-unsubscribe@xxxxxxxxxxxxxxx?subject=Unsubscribe> 
  

*	Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service <http://docs.yahoo.com/info/terms/> . 


<<attachment: winmail.dat>>



Home Back to the Home of PROJECT VIXEN 


Copyright ProjectVixen.com. All rights reserved.

Opinions expressed in posts reflect the views of their respective authors.
DMCForum Mailing List Archive  DMCNews Mailing List Archive  DMC-UK Mailing List Archive

This site contains affiliate links for which we may be compensated